Fishfinder will not "shoot" through hull

[BigDog216]

Hey everybody........newbie and 1st poster here.
Got a little problem maybe you guys can shed a little light on.
I have a Perception Caster 12.5 and a Humminbird Piranhamax 190c FF.
I mounted the transducer inside the hull laying flat on the bottom of the kayak....didn't glue it down yet as this was a test run......FF displayed 0 depth and no picture on the screen the entire time.....took the tranducer out and dangled over the side and it works perfectly.....:confused:
any ideas?

thanks in advance for the help

[salty pirate]

did you have any water inside the hull? if the transducer has air under it won't work. try a search

[mtnbykr2]

there are a whole bunch of tecniques for transducers in innovations or just serch it in here, marine goop works best imo...:reel:

[BigDog216]

Nope! no water in the hull....excuse my stupidity.....didn't find this forum til after I went fishing....gonna use the Goop method....thanks

[salty pirate]

Nope! no water in the hull....excuse my stupidity.....didn't find this forum til after I went fishing....gonna use the Goop method....thanks

be careful with the goop method if you get air bubbles in the goop you won't get a good pic. I saw someone posted transducer in a ziplock bag that has water in it. that might be a good way to test how shoot through hull works on your ff.
if temp is importent to you shoot through is not the way to go.

[mtnbykr2]

I have used the goop method 4 different times with no trouble, I like the
zip lock method too...:reel:

[sandydiego]

Nope! no water in the hull....excuse my stupidity.....didn't find this forum til after I went fishing....gonna use the Goop method....thanks

I have used the goop mount and switched to the wet mount. The FF will be much more sensitive with a wet mount. I can watch my weight on my sabiki drop to the bottom and adjust it to what ever depth with the wet mount. This is the best way to get the most out of any FF. Search wet mount and you will see what we are talking about. I am using a 5 inch pvc pipe with a rubber cap held down by a hose clamp. I check the water level before loading up to fish.

Good luck

Steve

[sandydiego]

[QUOTE=
if temp is importent to you shoot through is not the way to go.[/QUOTE]

My FF temp is spot on with the wet mount. I'm sure it depends on how much water/contact the wet mount has.

[maui jim]

That will $145.00 for the BWE Information fee....
Tax is included of course...:cool:

We accept beer, fish in trade and always cash...:cheers1:

[mtnbykr2]

:biggrinjester::biggrinjester::biggrinjester::luxh ello:

[salty pirate]

My FF temp is spot on with the wet mount. I'm sure it depends on how much water/contact the wet mount has.

Your right the temp of the water that's inside the 5" pvc inside the hull of the kayak couldn't dif-fer from that of the surface temp. ;)

[sandydiego]

Your right the temp of the water that's inside the 5" pvc inside the hull of the kayak couldn't dif-fer from that of the surface temp. ;)

The heat loss through the polyethylene hull is why it works. The PVC and cap just keep the water in place. We have compared it to a in the water mount and it read the same.

[tagyak]

http://www.bigwatersedge.com/bwevb/showthread.php?t=6394&page=5
take a look at this link. this is what i did for my wet mount. i used a container that i had bought lunch meat in from target and just cut out the bottom.
this has worked great for me. it holds the water tight with the lid and also the temp reading has been fairly accurate.
make sure to use a piece of foam to keep the transponder in place in the container. if you don't the transponder moves around and the reading will be off. i made this mistake so learn from me.

[sandydiego]

http://www.bigwatersedge.com/bwevb/showthread.php?t=6394&page=5
take a look at this link. this is what i did for my wet mount. i used a container that i had bought lunch meat in from target and just cut out the bottom.
this has worked great for me. it holds the water tight with the lid and also the temp reading has been fairly accurate.
make sure to use a piece of foam to keep the transponder in place in the container. if you don't the transponder moves around and the reading will be off. i made this mistake so learn from me.

Snap lock containers work great as well and you can screw the unit into the lid to hold it in place.

[Hunters Pa]

If you are really brave you could take this approach

http://www.kayaksportfishing.com/phpBB2/viewtopic.php?t=8407

[tagyak]

If you are really brave you could take this approach

http://www.kayaksportfishing.com/phpBB2/viewtopic.php?t=8407

nice! it has been a few years now, so how is it holding up? have you had to do any touch ups since then?
have you also been reluctant to upgrade your sonar unit or would you do it again?
just curious, thanks.

[Hunters Pa]

nice! it has been a few years now, so how is it holding up? have you had to do any touch ups since then?
have you also been reluctant to upgrade your sonar unit or would you do it again?
just curious, thanks.


No issues whatsoever. The 5200 cured/dried to be semi-flexible, like caulk. I would absolutely do it again, unless the kayak already had accomodations for the ducer being in the water, like the Tridents. The sonar unit I have has everything I need. If I'm going to drop the $ on a hi-end sonar then I'll probably be updating the ride as well.

[sandydiego]

No issues whatsoever. The 5200 cured/dried to be semi-flexible, like caulk. I would absolutely do it again, unless the kayak already had accomodations for the ducer being in the water, like the Tridents. The sonar unit I have has everything I need. If I'm going to drop the $ on a hi-end sonar then I'll probably be updating the ride as well.

I would love to get some 5200. I'ts just so damm much $$$$.

[mazilla]

I was having the same problem when I had mine mounted with 5200...so I ripped it out and re-bedded it with marine goop, problem solved.