Bait tank primer bulb?

[CheapPelican]

I'm kicking around ideas for a new bait tank. I want a scupper pick up and would like to avoid using a primer bulb if possible. My question is; How high can you mount a pump (http://www.kayakfishingsupplies.com/servlet/the-451/Tsunami-Pump/Detail) without needing a primer bulb.

[bus kid]

You don't need a primer bulb put a 90 deg elbow pointing forward, a little forward momentum will do the trick.

[theluckypig]

i use a separate male pvc fitting attached to a bulb pump. when ready to prime, i connect to the fitting / pump to the female inlet of my tank, a pump or two, primed, then remove the fitting / pump... ;) works for me...

[jorluivil]

You don't need a primer bulb put a 90 deg elbow pointing forward, a little forward momentum will do the trick.

This method works flawlessly.

[bus kid]

This method works flawlessly.

Its the Godfathers preferred method.

water pick up thru tank scupper. This is a similar variation of the Hobie tank set up.

cut down a 90 male 1" thread to 3/4 hose elbow so it fits in the channel flush, the screw splits the opening in half to keep debri out.

http://www.bigwatersedge.com/bwegallery/data/500/IMG_2357.JPG

http://www.bigwatersedge.com/bwegallery/data/500/IMG_2356.JPG

Easily changed out to most kayaks.....skanky after rain bay water:rolleyes:

http://www.bigwatersedge.com/bwegallery/data/500/IMG_2350.JPG

Simple way of getting that thru hull set up with out drilling those big holes. A little forward momentum is all it takes to prime/ 6 volt kept prime and worked well.

[CheapPelican]

You don't need a primer bulb put a 90 deg elbow pointing forward, a little forward momentum will do the trick.
Similar to the hobie livewells pickup, thought about it. The pump would be 1-1/2 to 2" higher than the hobie set up, and i figured it would need some extra help to get started. I guess I could experiment by wedging a couple 2x4s under the livewell.

Do you think running the pump off of 12v would give the pump extra oomph to pull the water uphill?

[GregAndrew]

12V is not going to help you with an impeller driven pump. There are problems with the elbow method also. You cannot strain the water coming in much at all without reducing the water flow enough to make it not work. So if you use that method, make sure your pump is accessible for cleaning in an emergency. Primer bulb cuts down on the flow except, in the case that James (luckypig) pointed out, where you temp attach it inside the tank until water flows.

[bus kid]

12V is not going to help you with an impeller driven pump. There are problems with the elbow method also. You cannot strain the water coming in much at all without reducing the water flow enough to make it not work. So if you use that method, make sure your pump is accessible for cleaning in an emergency. Primer bulb cuts down on the flow except, in the case that James (luckypig) pointed out, where you temp attach it inside the tank until water flows.

X2

[CheapPelican]

Guess I'll stop trying to re-invent the wheel :shot:

[RGB]

I'm doing a pretty similar setup right now and my plan is to use a one way check valve mounted on the pump inlet. This setup will still require priming which can easily be done by opening the pump housing and pouring a little water in. In my case, i'll be mounting the aerator head low on the tank so i'll also be able to partially fill the tank and it will self prime. I got some inspiration from here:http://www.bigwatersedge.com/bwevb/showthread.php?t=8310&highlight=bait+bucket&page=2