Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 02-18-2012, 08:51 PM   #1
steveooo
Senior Member
 
steveooo's Avatar
 
Join Date: Sep 2005
Posts: 1,921
Pimp My Yak





A few months back I got a phone call from Andy at OEX Sunset Beach with those magical words we all love to hear “ Your new kayak is here at the shop”.

Sweet! Upgraded from the Hobie Adventure to the Hobie Adventure. Actually, this is my 5th Hobie adventure. I like it for a few reasons. 1) It has lots of legroom 2) Big tankwell with lots of storage 3) Its FAST! 16 feet long, only 27.5 inches wide, the hull is really built for speed. 4) It paddles better than most paddle yaks I’ve tested. If I ever break a mirage drive (I’ve broken 4), I know its not going to be that big a deal to paddle back. Plus, if I ever get a decent fish, I like to put it in my lap and do a legit “happy paddle” back to shore. The main reason I wanted to upgrade to the new one, is that now there is a real cup holder, that holds a beer nice and snug without spilling. Plenty of these were consumed during this process.



Each one I get I rig a little different, tweaking things so that they are perfectly where I want them on the kayak. I like this one, but who knows- I’m sure the next one I’ll switch a few things around. My goal when I rig, is to simply make it easier out on the water. I really don’t do anything ground breaking, but here are the mods I do, which may get the wheels turning for you as you get the itch to tinker. This one took me about 20 visits to Andy’s shop in Sunset Beach. I never really knew what I wanted, but inevitably, I would find exactly what I needed. Warning, this won’t be a short post.

First thing I do is remove rigging. I get rid of this bungee, it just gets in the way.



I also get rid of the rod holder caps. I can’t ever see myself wanting to cap a rod holder?



I get rid of the mesh side pockets, or sabiki snaggers as I like to call them. After a few months in the sun and salt, they look like crap anyways.



I never use the peddle clip, so I get rid of it.



I put in one of these in its place.



Since I got rid of all the bungles, I swap out every one of these



For one of these. Now I have a few more places clip my bait tank, game clip, and rod leash, ect.



In the place of where the side pockets were, I permanently mount my knife



And My pliers.



I added a stainless snap onto the pliers sheath, so I don’t ever worry about losing them. I always leave both the knife and pliers on the yak, even when I transport it. That way I know I always have them both otw with me, and they will always be in the same exact place.

Swap the dinky stock rudder for the sailing rudder. Makes the 16’ adventure turn on a dime.



Take off this little mast cap



Put this in its place. Looks like a lot, but it is all there by design. Right to left- Ram ball for fishfinder, power cable for fishfinder, Ram wedgeball for my vhf, on/off switch for bait tank, Scotty for lights/camera/rodholders. I also use a Scotty clip to keep the power cable secured while not in use. Most days, I just bring my fishfinder out with me.



I use plenty of Marine Goop in this whole process. First use is to mount clips for my bilge pump. It always will be in the same spot if I ever need it.



I use plenty of marine Goop when I install the flush mount Scotty’s. This one was a little tricky, because I had the rudder adjustment line to deal with.



Here are the Scotty rocket launchers that go there. I only use these if I am fishing for Hali’s. Otherwise, they stay on shore.



This is where most people turn into a pussy. Take your brand new, never been in the water kayak, and cut a gaping 2” hole in the bottom.



Here is the transducer. Dual beam, gets perfect water temps, super clear picture, and it stays flush with the kayak. 3rd yak I’ve done this on, and I’ve never leaked a drop of water.



Here is the clean finished product. Wet mounts can suck it.



Next use for Goop. I don’t ever feel the need to pull my fishfinder cables apart on the water, and I hate corrosion. Started doing this a while back after I had some corrosion problems. After I coat the terminals with some dielectric grease I goop the fishfinder connections together, so there is not ever a chance that saltwater can get in to corrode. Been doing this for 5 years, no issues.



I also do a similar thing for all my electrical connections in the yak. It’s a little unconventional, but it works good. I’ve had past issues with corrosion when I use wire crimps, liquid tape, and di-electric grease. Now, when I do My electric connections, I simply tie the 2 wires together.



Then I coat them with some Marine Goop. Not the prettiest way, but it prevents corrosion.



Since the first hole in the bottom of the yak went so smooth, lets cut another.



This one is for the through hull bait pump.

Here is the internal plumbing



I put it in a place that is does not rub when I drag the yak across the sand.



Here is where is exits out of the kayak, with a male garden hose attachment. Also I added a Scotty mount back there for a light or camera.



Speaking of bait, here is the start of my tank.



I wanted a few different things out of my bait tank. I wanted to hold about 5 gallons. I wanted it round. I didn’t want much protruding into the bait tank like nozzles or screw heads. I wanted it to be low profile, to keep the center of gravity down and to avoid the wind.

After a little time with the sawzall, here is what I ended up with. I like it so far. I know the aluminum will hold up pretty well. Its actually deceptively big. Almost 5 gallons right now, I might drill the holes down a little lower to get it to 4 gal.



Here is the back of the tank.



Here it is strapped into the yak



Only 8 Inches tall, so it shouldn't pick up to much wind drag


Here is the interior. Notice, not much protruding into the tank to kill the bait.



Here is the garden hose connection going to the back of the tank.



There are a few reasons why I like doing the through hull bait pump. One reason, is that I don’t drag a pump in the water. The other reason is that I can switch bait tanks for different days. If I know I will load up on a ton of fin bait, the aluminum tank is good.
If I know I only need a couple pieces of squirts, and would prefer to keep the majority of the tankwell open for fish, I have this little 1 gallon tank. I know, technology at its finest.



Here is one bigger that I’m contemplating. It can hold 7.5 gal, which might be good if I know I'm only going to get a scoop of sardines and pound the sand. I’ll probably never get around to it though.



Instead of straps or bungees to attach the bait tank I found some 4mm rock climbing cord at REI. It tests out at almost 2000 lbs, which I think will be plenty. It also should do a decent job of avoiding hook snags. To make the attachment I loop it around the brass clip and tie it up with some stainless trolling wire.



Then I use a little heat shrink to make it look better.



I also make a 5’ section of this to use as my rod leash. Instead of individual rod leashes while surf landing, I loop this once around the rod & reel of each rig I have on board. Clip each side in, and everything is more than secure.



Here is my electrical system on the yak. I run a 12V battery for the FF, and a 6V pump for the bait tank. Both batteries are in this.



Here it is open.



I use a 2 pin trailer connection outside the box. A dab of Goop seals the hole up. The 12V is black, the 6V is painted white.



Here are the wires inside the yak. 12V Black, 6V White


My charger has the same 2 pin connection. I just plug the battery box straight to the charger, no messing around with alligator clips or anything.



Here are a few other add on items. For those that don’t like the Hobie seats, aftermarket seats should strap right in.



I always keep a leash on my mirage drive, and it is always attached to the yak. That way, if I ever take out the peddles OTW, I’m not worried about sending them into the drink.



A few people have asked how I mount my camera. Here is my set up. I run a Ram ball to a Scotty extension arm.



Here is the whole setup. I have a couple different Scotty mounts on the yak, so this system allows me the flexibility to put the camera in a few different locations on the yak. I think the PVC method looks a little cleaner though.



Lastly, here is what I use to get my yak junk from point A to point B. This has been a lifesaver since I downsized my vehicle from a big truck, to a 35mpg gas saver. Not rocket science, but I do have lots of guys ask about it. It fits my peddles, seat, waders, and anything else that isn’t permanently attached to the yak. Wal-mart has them.



Plus, they double as a cooler when you forget yours...



That’s about it. I’ve been meaning to put a post together like this for a while, because I have guys ask about my set-up pretty frequently. That, and now I have a little record of what I did. If you are unsure of what you need for rigging your yak up, I'd go see Andy at OEX Sunset beach. He's got plenty of supplies, and has rigged up a few yaks as well, so I'm sure he can help you out. Congratulations if you have made it this far into the post...

Steve


Last edited by steveooo; 02-19-2012 at 06:43 AM.
steveooo is offline   Reply With Quote
Old 02-18-2012, 09:08 PM   #2
MuddyMike
Senior Member
 
MuddyMike's Avatar
 
Join Date: Feb 2011
Location: Temecula, CA
Posts: 111
Quote:
This is where most people turn into a pussy. Take your brand new, never been in the water kayak, and cut a gaping 2” hole in the bottom.
What did you call me?

Nice rig, and some nice work!
MuddyMike is offline   Reply With Quote
Old 02-18-2012, 09:17 PM   #3
Mr. Adventure
Damn Hippy
 
Mr. Adventure's Avatar
 
Join Date: Nov 2011
Location: Riverside
Posts: 311
Fun post for sure man
Mr. Adventure is offline   Reply With Quote
Old 02-18-2012, 09:20 PM   #4
buttchaser
Float Tuber
 
buttchaser's Avatar
 
Join Date: Mar 2005
Posts: 243
Nice work , great tutorial !
buttchaser is offline   Reply With Quote
Old 02-18-2012, 09:37 PM   #5
The Kid
Loves Surface Irons
 
The Kid's Avatar
 
Join Date: Jun 2008
Location: San Diego
Posts: 455
I just witnessed the birth of a fishing monster!
The Kid is offline   Reply With Quote
Old 02-18-2012, 10:09 PM   #6
YakMedic
Senior Member
 
YakMedic's Avatar
 
Join Date: Feb 2011
Location: Wrightwood
Posts: 623
Damn Steveooo, that thing is sick
YakMedic is offline   Reply With Quote
Old 02-18-2012, 10:56 PM   #7
Bennyblanco
Ironman
 
Join Date: Sep 2011
Location: Inland empire
Posts: 175
When my balls grow bigger I will make a 2" hole and rig my hobie more professional.
Bennyblanco is offline   Reply With Quote
Old 02-19-2012, 12:25 AM   #8
dwntwnall4u
Kevin C.
 
Join Date: Aug 2011
Location: San Diego/Hawaii
Posts: 146
Very nice set-up. Where do you mount the battery box?
dwntwnall4u is offline   Reply With Quote
Old 02-19-2012, 06:04 AM   #9
Jimmyz123
Senior Member
 
Jimmyz123's Avatar
 
Join Date: Mar 2010
Location: San Diego
Posts: 2,385
Great work Steve, that was a fun post to read first thing in the morning, now I'm going to try and get out today. Very Motivating.
__________________
No better time than being on the water,

God Bless,
JimmyZ

Jimmyz123 is offline   Reply With Quote
Old 02-19-2012, 06:14 AM   #10
Salt Water Flies
Junior
 
Join Date: Feb 2012
Posts: 28
Very sweet looking rig. I'm headed to Florida in about a week and I'm in the process of rigging my new kayak and the wife's kayak too. I have the same bildge pump as yours. Where did you find the hanging clips for it? Again nice work. Tony
Salt Water Flies is offline   Reply With Quote
Old 02-19-2012, 06:52 AM   #11
T Bone
Senior Member
 
T Bone's Avatar
 
Join Date: Dec 2008
Location: Redlands CA
Posts: 871
I have had the same Kayak for five years and Steve is on his fifth Adventure.

Anyone want to buy a kidney,I am getting a PA somehow.
__________________
Barachit Baralah,Elohim-In the beginning,God-Genesis 1:1

"Who among you,if your son asked for a fish would give them a serpent " Jesus Matt. 7:10
T Bone is offline   Reply With Quote
Old 02-19-2012, 06:56 AM   #12
Holy Mackerel
Señor member
 
Holy Mackerel's Avatar
 
Join Date: Mar 2005
Location: San Diego, CA
Posts: 1,627
"legit happy paddle"

Nice, a lot of good ideas for rigging, thanks for sharing.
Holy Mackerel is offline   Reply With Quote
Old 02-19-2012, 07:22 AM   #13
ful-rac
Emperor
 
ful-rac's Avatar
 
Join Date: May 2009
Location: Buena Park
Posts: 3,649
Nice work there steve! Holes in the bottom of the yak.....! Fearless!
__________________
There's nothing colder than yesterday's hotdog.
ful-rac is offline   Reply With Quote
Old 02-19-2012, 07:56 AM   #14
echo1er
Senior Member
 
echo1er's Avatar
 
Join Date: Sep 2011
Posts: 598
what did I just witness. Kayak Porn!
echo1er is offline   Reply With Quote
Old 02-19-2012, 08:29 AM   #15
da22y
Senior Member
 
Join Date: Mar 2007
Posts: 265
Awesome post !
Finally Hobie adventure get some "exposure".
All the posting has been toward PA and Revo.

I like the way my Adventure paddle compare to my last revo, and the PA need even bigger arm muscle...

da22y is offline   Reply With Quote
Old 02-19-2012, 08:42 AM   #16
Big T
Member, You Member!
 
Big T's Avatar
 
Join Date: Jul 2011
Location: Lake Forest
Posts: 254
Droooooooool
Big T is offline   Reply With Quote
Old 02-19-2012, 08:43 AM   #17
echo1er
Senior Member
 
echo1er's Avatar
 
Join Date: Sep 2011
Posts: 598
Now I wanna see video's of this in the water! I'll sub to this channel
echo1er is offline   Reply With Quote
Old 02-19-2012, 08:44 AM   #18
StinkyMatt
Senior Member
 
StinkyMatt's Avatar
 
Join Date: Jun 2010
Location: Under a bridge
Posts: 2,168
Like a kid with a new bike....

And here I put in the basball card, just like this....listen to it when I go fast
Sweet ride Stevo.
StinkyMatt is offline   Reply With Quote
Old 02-19-2012, 08:51 AM   #19
lterrero
Leo
 
lterrero's Avatar
 
Join Date: Feb 2010
Location: La Jolla, CA
Posts: 482
That's Stevooo, thanks for the ideas & it looks bitching! nice work!
lterrero is offline   Reply With Quote
Old 02-19-2012, 09:28 AM   #20
premo
Senior Member
 
premo's Avatar
 
Join Date: May 2008
Location: costa mesa
Posts: 124
no seat heating system yet?
great job steve.
premo is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 06:47 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.