Don't try this - Kayak Fishing Adventures on Big Water’s Edge

fryguy · 07-25-2009, 12:54 PM

Lost my truck recently and decided to improvise a way down to the beach.

Worked for about 10min. - it was glorious, then it broke and I sent my kayak for a ride on its own.

there's an improved model in the works...

kurt · 07-25-2009, 01:25 PM

Quote:

it was glorious, then it broke

Design looks good. Use iron pipe instead of PVC.

Iceman · 07-25-2009, 01:27 PM

so did it flip due to the short wheel base or pvc failure per say?

dorf · 07-25-2009, 01:48 PM

Looks like it could use an extra support between the post under the seat and the support under the front hatch. That should support the frame and stiffen it. At first glance I would say that is where you may have lost it.

Great idea.

twitchy · 07-25-2009, 06:10 PM

This is an example of, "Where there is a will, there is a way".

Love it.

kareem korn · 07-25-2009, 08:24 PM

I think it's an excellent design in prototype material.

T12 · 07-25-2009, 08:24 PM

Great idea, hope round two works out better for you.

bigbarrels · 07-26-2009, 12:09 AM

whose jeep is that? would fit nicely on top of it! Good luck

h2ofishfo · 07-26-2009, 10:16 AM

try abs not pvc

stairman · 07-26-2009, 11:53 AM

sorry to hear about your loss of the truck that happens to many out of work general motors engineers!

fryguy · 07-26-2009, 12:53 PM

Quote:

Looks like it could use an extra support between the post under the seat and the support under the front hatch.

Point taken. The new design is reinforced in these areas and I think I'm gonna use the kayak itself as the main frame. There was too much swaying when I slowed down and caused the pvc glue to break at the joints. I'll be fishin in no time. too bad it's not ready today

punchjamesarnol · 07-26-2009, 03:59 PM

A couple of 1/4 self tapping screws in the joints with the glue would seal the deal! Awesom idea! double thumbs up!

beardedguy · 07-27-2009, 12:53 AM

Doesn't the trailer need a pivet point so that when the bicycle
leans into a turn the trailer can remain level with the ground.

beardedguy · 07-27-2009, 01:01 AM

By the way. Sway will usually occur if there is to much weight behind
the tires. If possible move the yak up the trailer or add some weight
in the front of the yak. If the weight is behind the tires it becomes the
greater force and will try to steer its self from the back.

Hunters Pa · 07-27-2009, 12:10 PM

Could beef up the pvc by using 1/2" inside 3/4". Adds to teh strengthe substantially.

Great innovation!

speedydk · 07-27-2009, 07:54 PM

I've been thinking about one of these for awhile now not cheap but looks pretty impresssive.
http://www.paddlecart.com/biketrailer.html

dsafety · 07-27-2009, 09:23 PM

Looks like a great design with lots of potential. If I were building it, I would use 2" ABS rather than PVC and run a line or cable from the anchor point on the bike through the pipe to a place near the wheels. I would put some tension on the cable so it becomes kind of an internal safety strap.

If you can identify some places that tend to flex too much, just cut a larger piece of pipe in half and glue it to the flex points.

You have two flex points that, unless you figure out how to brace them, will always be a problem. They are at the seat and at the 45 degree angle over wheel. You could create a different kind of connection at the seat that pivioted up and down as well as right and left. The 45 degree connection needs to be really beefed up. I bet that is where the thing broke.

Bob

Matt · 07-27-2009, 09:33 PM

Two words ......DUCT TAPE!!!

07-25-2009, 01:27 PM	#3
Iceman Administrator Join Date: Mar 2005 Location: 1-2 miles off the point Posts: 6,943	so did it flip due to the short wheel base or pvc failure per say? __________________

07-25-2009, 01:48 PM	#4
dorf Senior Member Join Date: Nov 2007 Location: San Diego Posts: 279	Looks like it could use an extra support between the post under the seat and the support under the front hatch. That should support the frame and stiffen it. At first glance I would say that is where you may have lost it. Great idea. __________________ Don't try to confuse me with facts! I hereby reject your reality and submit my own.

07-27-2009, 09:33 PM	#18
Matt Support your local pangas Join Date: Feb 2007 Location: Lj Posts: 976	Two words ......DUCT TAPE!!! __________________ Thanks Matt F.

07-25-2009, 06:10 PM	#5
twitchy Member Join Date: Apr 2007 Location: Carlsbad, CA Posts: 61	This is an example of, "Where there is a will, there is a way". Love it.

07-25-2009, 08:24 PM	#6
kareem korn Senior Member Join Date: May 2006 Location: C-bad Posts: 431	I think it's an excellent design in prototype material.

07-25-2009, 08:24 PM	#7
T12 Member Join Date: Aug 2007 Location: vista Posts: 36	Great idea, hope round two works out better for you.

07-26-2009, 12:09 AM	#8
bigbarrels Senior Member Join Date: Aug 2008 Location: Vista Posts: 1,111	whose jeep is that? would fit nicely on top of it! Good luck

07-26-2009, 10:16 AM	#9
h2ofishfo Senior Member Join Date: Feb 2007 Location: Santee Posts: 821	try abs not pvc

07-26-2009, 11:53 AM	#10
stairman Member Join Date: Jun 2009 Posts: 84	sorry to hear about your loss of the truck that happens to many out of work general motors engineers!

07-26-2009, 03:59 PM	#12
punchjamesarnol Member Join Date: May 2009 Location: Santuckee Posts: 33	A couple of 1/4 self tapping screws in the joints with the glue would seal the deal! Awesom idea! double thumbs up!

07-27-2009, 12:53 AM	#13
beardedguy gurmpy old one Join Date: Apr 2007 Location: El Cajon Posts: 80	Doesn't the trailer need a pivet point so that when the bicycle leans into a turn the trailer can remain level with the ground.

07-27-2009, 01:01 AM	#14
beardedguy gurmpy old one Join Date: Apr 2007 Location: El Cajon Posts: 80	By the way. Sway will usually occur if there is to much weight behind the tires. If possible move the yak up the trailer or add some weight in the front of the yak. If the weight is behind the tires it becomes the greater force and will try to steer its self from the back.

07-27-2009, 12:10 PM	#15
Hunters Pa Senior Member Join Date: Jul 2006 Location: Fullerton Posts: 1,358	Could beef up the pvc by using 1/2" inside 3/4". Adds to teh strengthe substantially. Great innovation!

07-27-2009, 07:54 PM	#16
speedydk Member Join Date: Mar 2008 Location: Orange County Ca. Posts: 99	I've been thinking about one of these for awhile now not cheap but looks pretty impresssive. http://www.paddlecart.com/biketrailer.html

07-27-2009, 09:23 PM	#17
dsafety Olivenhain Bob Join Date: May 2008 Location: Olivenhain, CA Posts: 1,121	Looks like a great design with lots of potential. If I were building it, I would use 2" ABS rather than PVC and run a line or cable from the anchor point on the bike through the pipe to a place near the wheels. I would put some tension on the cable so it becomes kind of an internal safety strap. If you can identify some places that tend to flex too much, just cut a larger piece of pipe in half and glue it to the flex points. You have two flex points that, unless you figure out how to brace them, will always be a problem. They are at the seat and at the 45 degree angle over wheel. You could create a different kind of connection at the seat that pivioted up and down as well as right and left. The 45 degree connection needs to be really beefed up. I bet that is where the thing broke. Bob