Transducer on Extreme - Kayak Fishing Adventures on Big Water’s Edge

drmboy · 03-03-2006, 11:41 PM

I just purchased a humminbird 383c fish finder and i was wondering where to put the transducer. I know most people do the in hull type but it says that the temp readout doesnt work and that the depth might not be correct. I have that option or i could mount it at the back of the kayak and have it in water and drill holes in the back for wires and so on. My question is why does everyone mount it inside if it makes the readings less accurate?

madscientist · 03-04-2006, 03:37 AM

Only the temp is inaccurate, the depth readings are fine.

scwafish · 03-04-2006, 07:15 AM

On an eXtreme you will have to remove the foam in your mounting location for it to work correctly. Not difficult, but a bit of a PITA. I have found the temp to work ok too, it just takes a while for the hull to reach the same temp. as the water.

tattuna · 03-04-2006, 07:29 AM

I just jammed my puck into the larger scupper hole under the seat with a little bit of Shoe Goo on the sides of it. You have to drill a hole to run your cables through, but you can seal it afterwards. I've had it like this for a year and a half without any problems.

scwafish · 03-04-2006, 08:47 AM

I had thought about that...does it still let water out of the scupper or did it plug it completely? That would give you a super clean signal...me likey!!

tattuna · 03-04-2006, 09:02 AM

Water still comes through the scupper. I could'nt jam it in enough to plug it up, but it's deep enough to where it's submerged just below being flush with the bottom.

FishingPlanner · 03-04-2006, 09:22 AM

I seem to get a fairly accurate temp reading thru the hull, though as scwafish pointed out it takes a while for the hull to get to the same temp as the water.

I also like tatuna’s idea. I might give that a try next time around.

-Kevin

scwafish · 03-04-2006, 03:10 PM

Thanks Tattuna, I'm doing my next boat that way...very cool.

03-03-2006, 11:41 PM	#1
drmboy Junior Member Join Date: Jan 2006 Posts: 8	Transducer on Extreme I just purchased a humminbird 383c fish finder and i was wondering where to put the transducer. I know most people do the in hull type but it says that the temp readout doesnt work and that the depth might not be correct. I have that option or i could mount it at the back of the kayak and have it in water and drill holes in the back for wires and so on. My question is why does everyone mount it inside if it makes the readings less accurate?

03-04-2006, 09:22 AM	#7
FishingPlanner Junior Member Join Date: Feb 2006 Posts: 3	I seem to get a fairly accurate temp reading thru the hull, though as scwafish pointed out it takes a while for the hull to get to the same temp as the water. I also like tatuna’s idea. I might give that a try next time around. -Kevin __________________ www.sdfinancialplanning.com

03-04-2006, 03:37 AM	#2
madscientist Senior Member Join Date: Mar 2005 Posts: 1,906	Only the temp is inaccurate, the depth readings are fine.

03-04-2006, 07:15 AM	#3
scwafish Member Join Date: Mar 2005 Location: Ukiah Posts: 86	On an eXtreme you will have to remove the foam in your mounting location for it to work correctly. Not difficult, but a bit of a PITA. I have found the temp to work ok too, it just takes a while for the hull to reach the same temp. as the water.

03-04-2006, 07:29 AM	#4
tattuna Senior Member Join Date: Mar 2005 Location: Pasadena Posts: 329	I just jammed my puck into the larger scupper hole under the seat with a little bit of Shoe Goo on the sides of it. You have to drill a hole to run your cables through, but you can seal it afterwards. I've had it like this for a year and a half without any problems.

03-04-2006, 08:47 AM	#5
scwafish Member Join Date: Mar 2005 Location: Ukiah Posts: 86	I had thought about that...does it still let water out of the scupper or did it plug it completely? That would give you a super clean signal...me likey!!

03-04-2006, 09:02 AM	#6
tattuna Senior Member Join Date: Mar 2005 Location: Pasadena Posts: 329	Water still comes through the scupper. I could'nt jam it in enough to plug it up, but it's deep enough to where it's submerged just below being flush with the bottom.

03-04-2006, 03:10 PM	#8
scwafish Member Join Date: Mar 2005 Location: Ukiah Posts: 86	Thanks Tattuna, I'm doing my next boat that way...very cool.