drive rubbing

[driftwood]

Whoa nelly!!!!! Look at that gap on those drums! A gap that big on your drums is like having a real bad front wheel alignment on your car. Your tires are not going to wear evenly. Replace the drums ASAP!

[Iceman]

drums are $16.50 a piece, I am guessing those saw an extended period of loose chains/cables at one time.

[jorluivil]

Originally Posted by Iceman

drums are $16.50 a piece, I am guessing those saw an extended period of loose chains/cables at one time.

Andy, when the drums are changed are there any non-reusable parts that would also need to be replaced?

Originally Posted by jorluivil

Andy, when the drums are changed are there any non-reusable parts that would also need to be replaced?

No...

Mirage drives are actually incredibly simple. In order to service them you only need two open ended wrenches and a alan wrench.

Paper towels, q-tips, soapy water, and grease

Unless your cables are stretched to the point of the lock nuts being bottomed out, or your main axel has grooves from friction; there is nothing else you would need to change.

[jorluivil]

Originally Posted by Drake

No...

Mirage drives are actually incredibly simple. In order to service them you only need two open ended wrenches and a alan wrench.

Paper towels, q-tips, soapy water, and grease

Unless your cables are stretched to the point of the lock nuts being bottomed out, or your main axel has grooves from friction; there is nothing else you would need to change.

Sounds good! I have some side to side wiggle on my drives, I need to change my drums before they start looking like Mr Jones' drive.

Originally Posted by jorluivil

Sounds good! I have some side to side wiggle on my drives, I need to change my drums before they start looking like Mr Jones' drive.

Before you change your drums follow Steveooo's post here. I'm going to do a much more detailed one next time I do my drives.

I take all 6 nuts off so the chain will stay in the same place on the sprocket but to each their own.

The side to side slop will be mostly come from a loose idler cable (the one without the chain) give it a few turns on each side equally and as long as you're not bottomed out, it will tighten them up.

Also, when you pull the drums off and clean off your main axel, the regreasing of it will add more of a buffer between the drum hole and the axel so it won't wiggle as much. Be as generous as you can with the grease, the more you have the more difficult it is for sand to penetrate it's way into the space between the two.

Since the plastic is softer than the metal, the sand will "stick" or "embed" in the drums plastic. People are always surprised when the axel wears more than the drum itself but it's because the axel is rubbing on the sand and the sand remains in place on the drum.

Make sense?

[RobFish]

You can always have your mechanic spin their magic wrenches for you too.
Had mine done recently, and the difference is truly amazing.
No clicking or noise, no slop or wiggle, just beautiful Mirage motivation.
Props to my mechanic.

[Dannowar]

TRUST your mechanic

[TJones]

it is pretty obvious in picture. at least 1 mm gap. and of course noticeable slop in drive mechanism .that might be why i am having contact on side of drive bay. my drive is a 2010 and i think i did not lube the shaft until recently. when i took the yak out , it would be for long hours on water . i probably should have broken it down and lube it more often . i might just pick up a new drive and then start rebuilding this one as a backup . anyone else have any opinions ?

[TJones]

on the forum?

[driftwood]

Whats wrong with just calling Andy on the Phone?

Originally Posted by TJones

i might just pick up a new drive and then start rebuilding this one as a backup . anyone else have any opinions ?

Yeah... just buy two new drums and an axel. It will take 10 minutes to replace. Why spend $500 on a drive?

Also, since you have this problem. I wouldn't be surprised if the shaft running through your fins has a lot of wear on them too.

I take apart and clean my drives once a month.


Which do you prefer?

Preventative Maintenance:

The care and servicing by personnel for the purpose of maintaining equipment and facilities in satisfactory operating condition by providing for systematic inspection, detection, and correction of incipient failures either before they occur or before they develop into major defects.


Corrective Maintenance:

Corrective maintenance is a maintenance task performed to identify, isolate, and rectify a fault so that the failed equipment, machine, or system can be restored to an operational condition within the tolerances or limits established for in-service operations.

[TJones]

i should break em down every now and then . how do i find the post on adjusting the drive?

[TJones]

found link.

[driftwood]

Or you can sell that drive to me cheap. I'll slap on a new set of drums in 15 min and have a like new drive.

[DanaPT]

systematic inspection, detection, and correction of incipient failures either before they occur or before they develop into major defects.

that's deep. I'm taking my drive apart this weekend.