Permanent Wet Transducer Installation - Kayak Fishing Adventures on Big Water’s Edge

THE CALI HOOKUP! · 01-19-2010, 06:45 PM

can the transducer still read through the abs matirial, Of course it sends a signal down then the signal spreads out untill it hits the bottom of the ocean. will this matirial mess up any readings because of how dense the matirial is.

The only problem I have is mounting the transducer to the cap, but I am sure I can figure it out, I have a question how close can you let the transducer get to the hull of the kayak with this type of install

Pm me if you have the answer

grey zone · 01-20-2010, 12:38 PM

I use a similar system that is a little more simple and works well. I have a small hard plastic box that is directly gooped to the inside of the kayak. The box is big enough for the transducer to sit in and the sides are 3" high. The bottom of the box was not removed so leaks are not a problem. I place the transducer in the box and add 1-2" of water and its good to go. I do not use a lid and water splashing out has never been a problem. You do not need much water. The depth finder I use is a Garmin and the picture is great.

dtownfan · 02-18-2010, 08:00 PM

dsafety...........i keep looking over your wet mount install and second guessing my future attempt at rigging my hummingbird. as of right now i have the hummingbird kit (sitting on the shelf) that craddles the tranny in marine grease. i pick up my yak next weekend and wonder......what will i do. i see the ease of moving the unit to other kayaks (i will only have one option there though) but if the sonar readings are better in water than grease well.....(would the grease make the hummingbird kit a wet mount?) i wonder how well the grease will do upside down if i ever have to store or transport that way.

are you still havin good results from the wet mount?

sorry to bring all this back up - just curious to learn more from your experience. any advice of things you would keep the same/change would be sweet!

dsafety · 02-18-2010, 09:37 PM

Quote:

Originally Posted by dtownfan

dsafety...........i keep looking over your wet mount install and second guessing my future attempt at rigging my hummingbird. as of right now i have the hummingbird kit (sitting on the shelf) that craddles the tranny in marine grease. i pick up my yak next weekend and wonder......what will i do. i see the ease of moving the unit to other kayaks (i will only have one option there though) but if the sonar readings are better in water than grease well.....(would the grease make the hummingbird kit a wet mount?) i wonder how well the grease will do upside down if i ever have to store or transport that way.

are you still havin good results from the wet mount?

sorry to bring all this back up - just curious to learn more from your experience. any advice of things you would keep the same/change would be sweet!

I have no experience with the "grease mount" so I cannot help you there. I can tell you that my unit, along with my kayak has been stored upside down for weeks and transported the same way. There have been no leaks and the performance has been excellent, (except for a flaky problem common to many Humminbirds when they suddenly stop showing any depth readings for a while).

My guess is that you could use grease instead of water in my design and everything would work fine. On a really hot day, the grease could liquify and cause some problems, especially if you stored or transported your yak upside down.

I like this design because it is so easy to install and there is virtually no chance of screwing anything up as you can with a goop or epoxy installation. The portability is is nice feature as well.

I hope this helps.

Bob

01-19-2010, 06:45 PM	#1
THE CALI HOOKUP! Junior Join Date: Dec 2009 Posts: 17	can the transducer still read through the abs matirial, Of course it sends a signal down then the signal spreads out untill it hits the bottom of the ocean. will this matirial mess up any readings because of how dense the matirial is. The only problem I have is mounting the transducer to the cap, but I am sure I can figure it out, I have a question how close can you let the transducer get to the hull of the kayak with this type of install Pm me if you have the answer

01-20-2010, 12:38 PM	#2
grey zone Senior Member Join Date: Mar 2005 Location: san diego Posts: 158	I use a similar system that is a little more simple and works well. I have a small hard plastic box that is directly gooped to the inside of the kayak. The box is big enough for the transducer to sit in and the sides are 3" high. The bottom of the box was not removed so leaks are not a problem. I place the transducer in the box and add 1-2" of water and its good to go. I do not use a lid and water splashing out has never been a problem. You do not need much water. The depth finder I use is a Garmin and the picture is great.

02-18-2010, 08:00 PM	#3
dtownfan Member Join Date: Jan 2010 Location: Northern Virginia Posts: 50	dsafety...........i keep looking over your wet mount install and second guessing my future attempt at rigging my hummingbird. as of right now i have the hummingbird kit (sitting on the shelf) that craddles the tranny in marine grease. i pick up my yak next weekend and wonder......what will i do. i see the ease of moving the unit to other kayaks (i will only have one option there though) but if the sonar readings are better in water than grease well.....(would the grease make the hummingbird kit a wet mount?) i wonder how well the grease will do upside down if i ever have to store or transport that way. are you still havin good results from the wet mount? sorry to bring all this back up - just curious to learn more from your experience. any advice of things you would keep the same/change would be sweet!