Share Your Innovations

[Flyfisher70]

This not really an innovation, it's cheap and keeps things real simple and functional.

All that's needed is black Sharpie marker and tape measure. Makes for easy fish measuring.



I'm right handed so I just put the measurements on the right hand side. I might ad the measurements lines on the other side of the Xfactor as well.

[Flyfisher70]

These are just some things I've seen and read about on this site and others. Lots of cool innovations for sure. I wish I could have contributed some of my own ideas, but I'm just not one of the creative type. Anyhow I hope these photos can help others out as past images and instructions have helped me out.

Bait tank battery box mounted directly onto the crate with zip ties. I drilled out two holes for each zip tie on the inside of the box (a total of four zip ties were used), once the zip ties were through the battery box and tight to the box I added marine goop to keep the water from entering through the holes.


I'm using this type of deck connector from the bait pump to the battery box. It seem like it could come unplugged really easy but we'll just wait and see how it works out.




The other side of the battery box has a toggle switch for turning the power on and off as needed.


ABS pipe cut to about twelve inches and then zip tied to the crate. The small cord is for tying down the rods just in case I roll while out on the water, so hopefully I will not loose any of my gear.


On the Vittles Vault bait tank I drilled some small drain holes, these work perfect with the Rule 360 bilge/bait pump and a 6v 7ah battery with the Mojo timer set at a fifteen seconds on and fifteen seconds off cycle.


On the lid of the bait tank I drilled out a small hole to put the cord through so that I will not accidentally loose the lid while on the water or land for that matter.


This just a small knot tied on the inside of the lid, simple yet effective.


Thanks for the great ideas guys!

[wiredantz]

Well being the professional yard sales man that i am.

I started thinking of new ways to stow my gear on my X-factor when i am launching and landing.








After i got tired of my transducer falling off while carrying it upside down i made my transducer act exactly like a rudder i even attached a pull string to come up when landing and launching.

[old_rookie]

Cool. I like the under hatch stowage area. I am your apprentice in landing yard sales.
Where do you get the bungie strings?

[wiredantz]

You get it by the foot from. Andy at oex or oex in San diego

[tagyak]

i like how you have a deployment system for the transducer.
it looks great, but most people say that you would want the transducer up front rather than in the back. this way it would show the fish that you are going over rather the fish that you already had passed???? unless of course if they are coming from behind you.....

[reefer]

Originally Posted by tagyak

i like how you have a deployment system for the transducer.
it looks great, but most people say that you would want the transducer up front rather than in the back. this way it would show the fish that you are going over rather the fish that you already had passed???? unless of course if they are coming from behind you.....

When I got my boat, the transducer was also mounted on the back. I questioned that too, but most FF have a WIDE sonar, so it wont really matter of the location. I would rather have mind in the water, reading the Temp, and getting the best reading out of it.

This is the way went about it, work great.

http://palmettokayakfishing.blogspot...-for-2012.html

[dc1983]

I recently added a new seat to my kayak. It consists of a Bass Pro folding boat seat with a boat seat swivel. Then I put a Wise Quick connect boat seat mount on the kayak.

materials used-
Bass Pro Folding boat seat-24.99
Bass Pro Boat seat swivel- 9.99
Wise Quick Connect Boat seat mount 20.99
screws/bolt/washers- like $15 (had to go back and get longer bolts)
scrap wood
tube of Marine Goop

Screws/bolts/washers were
1/4 in by 5 in X 4
1/4 in by 3 in X 4
1/4 in bolts X 8
washers X 24

Ok now to how it all went together-

I cut the scrap wood to fit the match the Wise Quick connect. Then drilled the holes to mount the quick connect to the wood. I used the wood with holes drilled as a guide and drilled the holes into the kayak. once this was done I placed the wood block and Quick connect together and used over 3/4 of the Marine Goop on the bottom of the wood and placed the weather stripping around the edges of the wood. then bolted it all in to where the seat would go.


On the top of the Wise quick connect I had to unscrew the top lip and place washers under the piece of metal to allow the base for the seat to slip in.

I drilled out the holes in the seat to connect the seat to the swivel base to allow for a better hold (the screws that come with the seat seem weak to me) For the Stealth 14 because of the bait tank hatch I had to cut out a little bit of the front center of the seat to beable to open the hatch.

Then put it all together and here is the end result. I used a Drimal tool to sand down all the edges that were still touching the kayak and causing friction.(pretty much just the back of the folding seat and the back corners on the bottom.

I took it out to Dana Point last weekend to test it out. The seat didn'e really change the center of Gravity. It felt the same as before I installed the seat as far as stability goes. I caught a 18 lb Halibut and never felt that I was going to tip over.

Another good thing i found is by Installing the seat this way it creates a space below the seat for more storage. My Nalgene bottle will fit under the seat perfectly.

Hope this helps those that had questions and feel free to ask all the questions you want. Next project is a trolling motor and I WILL be asking lots of Questions. My Goal is to make this stealth 14 better than a Pro Angler!!