My Bait Tank Ideas - Kayak Fishing Adventures on Big Water’s Edge

trunknuts · 09-16-2010, 07:59 AM

I'm new to this whole kayak fishing thing, so I'm trying to understand what you are trying to accomplish with the reverse polarity switch. Did you wire this up so that it can drain the water in your tank? If so, wouldn't the check valve on your pickup tube keep the water from dumping? Please excuse me if I'm not understanding your setup, I'm just curious since I will be building one of these soon. Thanks.

BTF_David · 09-16-2010, 08:53 AM

Quote:

Originally Posted by trunknuts

I'm new to this whole kayak fishing thing, so I'm trying to understand what you are trying to accomplish with the reverse polarity switch. Did you wire this up so that it can drain the water in your tank? If so, wouldn't the check valve on your pickup tube keep the water from dumping? Please excuse me if I'm not understanding your setup, I'm just curious since I will be building one of these soon. Thanks.

Hi TrunkNut,
The reverse polarity is to pull water into the tank at a slower rate than the 6v at normal polarity. It basically reverses the turning of the motor and impeller, thereby making the impeller less efficient...bringing less water per turn. The Youtube video link shows the flow of the water with normal polarity and reverse polarity visually to help you understand.

When filling the tank, I like to go at normal polarity to make that process happen quicker. Also, if I need the water changed in the tank quicker, I switch to normal polarity.

But for delicate bait fish or my "normal" operation, I like the reverse polarity because the water rate is slower entering the tank. A bonus effect is the water exiting the drain is less...so there is less of the trickling noise you hear from the drain operating.

Hope that makes sense. Holler if it doesnt.

-BTF_David

Iceman · 09-16-2010, 09:57 AM

Quote:

I usually prime at launch and it takes only a few seconds. A simple quarter twist opens up the motor and I pour 1/4 of a water bottle into to prime the pump. The check valve keeps the prime till I am ready to hit the switch to turn it on. It's easy to open up the pump on the water too.

Thanks for clarifying.

I use my multi purpose

gatoraide bottle for the same purpose as sometimes my intake needs a little push.

Kesepton · 09-16-2010, 11:58 AM

So DSafety, that attachment is for keeping water in the tank without the pump on right?

Thats a good Idea about blowing through it though. I think its worth adding it just for that feature!

dsafety · 09-16-2010, 12:28 PM

Quote:

Originally Posted by Kesepton

So DSafety, that attachment is for keeping water in the tank without the pump on right?

Thats a good Idea about blowing through it though. I think its worth adding it just for that feature!

The Hobie tank switch is placed in a location where it is very easy to accidentally turn the motor off when reaching back for a rod. I do it several times each trip. If you install the riser tube, you can keep the water from draining out if, (when) this happens and hopefully not kill your bait.

If you want to get more oxygen to the bottom of the tank, twist the tube to the drain position while keeping the motor on. Just don't forget to put it back in the vertical position or you run the risk of having the tank drain the next time you accidentally bump the switch.

As for using the tube to blow away debris, I initially tried the screen method but found that it would often get fouled with very small particles of kelp, whale snot or other things that would impede the flow. This is a much simpler way to solve the problem and it only takes seconds.

Bob

BTF_David · 09-16-2010, 12:35 PM

dsafety...your solution to the mentioned problem with the Hobie bait tank is creative. Thanks for sharing.

I can see how the push/pull method of their on and off switch can lead to accidental bumping.

newguy01 · 09-16-2010, 03:47 PM

btf i use to use the johson 500 pump and it failed on me numerus times using 6v the suction is not that strong for a thru scuper installation if you end up using 12v youl be fine. i sugest pay a little bit for the pump and get a tsunami from oex or if your lucky i think wallmart use to carry it.
now i have no problem on my home made tank, i like the rest of your ideas, i think i might change tank set up a little bit finness and thanks for your ideas

09-16-2010, 07:59 AM	#1
trunknuts Junior Join Date: Sep 2010 Posts: 2	Reverse Polarity Switch I'm new to this whole kayak fishing thing, so I'm trying to understand what you are trying to accomplish with the reverse polarity switch. Did you wire this up so that it can drain the water in your tank? If so, wouldn't the check valve on your pickup tube keep the water from dumping? Please excuse me if I'm not understanding your setup, I'm just curious since I will be building one of these soon. Thanks.

09-16-2010, 03:47 PM	#7
newguy01 Senior Member Join Date: May 2007 Location: S.D. Posts: 133	pump? btf i use to use the johson 500 pump and it failed on me numerus times using 6v the suction is not that strong for a thru scuper installation if you end up using 12v youl be fine. i sugest pay a little bit for the pump and get a tsunami from oex or if your lucky i think wallmart use to carry it. now i have no problem on my home made tank, i like the rest of your ideas, i think i might change tank set up a little bit finness and thanks for your ideas

09-16-2010, 11:58 AM	#4
Kesepton Member Join Date: Feb 2010 Posts: 70	So DSafety, that attachment is for keeping water in the tank without the pump on right? Thats a good Idea about blowing through it though. I think its worth adding it just for that feature!

09-16-2010, 12:35 PM	#6
BTF_David Member Join Date: Aug 2010 Posts: 30	dsafety...your solution to the mentioned problem with the Hobie bait tank is creative. Thanks for sharing. I can see how the push/pull method of their on and off switch can lead to accidental bumping.